Four line contact. Rotates ¼ " diameter test pin (journal) against two ½" diameter vee blocks (bearings).
Loads:
Spring type dual range gage applies from 200 to 3000 lbs. Direct load, ±2% full scale accuracy, (4500 lb. reference
load), approximately 3000,000 psi maximum average hertz stress. Spring type low load gage applies from 200 to 800
lbs ±2% full scale direct load providing improved accuracy when testing at these loads. Electronic load with digital
display, two ranges available, either 3000 lb. direct load gage or 1000 lb. direct load gage.
Speeds:
Standard spindle speed is 290 ±10 rpm (18.98 fpm).
Wear:
Micrometer type system allows rate of wear measurement during test and total wear.
Torque:
Indicating direct gage (0 to 150 in.lb ±2% full scale accuracy) or recording measurement and display system (0 to 100
in.lb, ±2% full scale accuracy).
Environments:
Liquid or dry tests. Liquid heater with manual control to 150° C. (302° F).
Institute of Petroleum Test Methods:
IP 241 Extreme Pressure Properties, Anti-Wear, Friction and Corrosion Protection Properties of Fluid Lubricants: Falex
Machine
MIL-L-63460D Lubricant, Cleaner and Preservative for Weapons and Weapon Systems
Federal Test Methods:
FTM-791-3807.1 Wear Life of Dry, Solid Film Lubricants
FTM-791-3812.1 Load Carrying Capacity of Dry, Solid Film Lubricants
Chrysler Corporation Specifications:
461-C-84-01 Load Carrying Capacity Test on E.P. Lubricants
461-C-84-02 Wear Test for Chemical Activity or Abrasiveness of E.P. Lubricants
401-C-84-03 Test for Potential Corrosiveness of Gear Lubricants
Ford Motor Company Specifications:
FMC-BJ1-1 Quality Laboratory and Chemical Engineering Physical Test Methods-Extreme Pressure Test on Oils
F-1500 STANDARD FALEX PIN & VEE BLOCK TEST MACHINE PACKAGE COMPLETE
220V, 50/60 Cycles. Items included with package:
Dual Range Load Gage
Load Gage Stand
Electronic Digital Indicating Torque Gage
Fluid Sample Cup
Manual Heater Control Shear Pin Knock-out Tool
Ratchet Wheel Loading Assembly
Brinell Load Calibration Kit
Shear Pin Clip & Puller
50 Complete Sets of Test Specimens with #8 Pins
F-1500C PIN & VEE BLOCK TEST MACHINE WITH COMPUTERISED DATA ACQUISITION SYSTEM - 50 / 60 Cycles
Standard Falex Pin & Vee block Test Machine with computerised data acquisition system to acquire, display, and
store torque with high limit cut-off, load, and temperature. The data is stored in a format compatible with
commercially available spreadsheet software packages (not included) and may be viewed in alphanumeric or
graphic format. Real time and historical trending can be displayed. Includes the following
Electronic Load System
Load Gage Stand
Ratchet Wheel Loading Assembly
Fluid Sample Cup
Manual Heater Control Shear Pin Knock-out Tool
Thermocouple and Retaining Clip
Electronic Load Calibration Kit
Shear Pin Clip & Puller
50 Complete Sets Test Specimens with #8 Test Pins
Data Acquisition System Includes:
IBMR Computer System
Internal Cartridge Tape Drive
Colour Monitor
Hard Disk Drive 3.5 inch Floppy Disk Drive
Keyboard & Mouse
MS-DOS, WindowsR
Falex Data Acquisition Programme
PLEASE NOTE: The data acquisition system is an integrated system for acquiring test data on the Falex Pin and Vee
block Test Machines. Use of the computer for other than intended design may affect warranty or equipment
performance. Equipment should be stored and operated in an air conditioned environment.
STANDARD FALEX TEST SPECIMENS
Each Falex test requires one set of test specimens, consisting of two V-Blocks, one Test Pin and one Shear Pin.
F-1500-50A Complete Sets:
Standard Falex Test Specimens include two V-Blocks of AISI 1137 Steel, one #8 Test Pin of SAE 3135 Steel and one
shear pin ASTM Spec. B-16. These specimens conform to ASTM Standards D-2670, D-2625 and D-3233.
F-1500-50B Complete Sets:
Same as F-1500-50A only with #10 pins substituted for #8 pins.
주문하세요
